All Zero Paints dry matt and require clearcoating unless otherwise specifiedApplication Notes :Zero Paints are pre-thinned for Airbrush use. Shake container until paint is thoroughly mixed. Spray at 15 - 40 psi,3 - 4 medium cross coats are recommended. Air drying at 20°C Dust-free: 5 – 10 mins, Tack-free: 20 - 30 mins. For additional thinning use Basecoat Thinners. Which Airbrush Cleaner should I use ?You can use either use Zero Paints Airbrush Cleaner or Basecoat Thinners, alternatively any thinners that contain Toluene should work, but it's best to test first. DO NOT use White Spirt or Acrylic Thinners, they are not suitable. |
 |
Health and Safety Notes :Harmful by inhalation. Irritating to eyes. Keep away from sources of ignition. NO SMOKING. Avoid contact with skin and eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Wear suitable gloves. Use in a well ventilated area. Keep out of reach of children. Please download the Material Safety Datasheets here -> |
STARTER PACK - 2 Pack GLOSS Clearcoat Set (2K Urethane)
This product has been replaced with ZP-3035 Diamond Finish - 2 Pack GLOSS Clearcoat System (2K Urethane) 220ml
2 Pack Clear Coat 100ml (Urethane)
Pack Contents :
- 1 x 100ml Clear Coat (High Solid) also known as Urethane or Polyurethane ()
- 1 x 60ml Hardener ()
- 1 x 60ml Thinners ()
- Instructions
Starter Pack also includes
- Mixing Sticks
- Graduated Beakers
- Transfer Pipettes
Mixing Ratio
100 Parts Clear, 50 Parts Hardener + 10-30% Thinners
(e.g. 50ml Clear, 25ml Hardener + 15ml Thinners).
Drying Times : Air Drying at 20°C, Dust Free 30 Mins, Tack Free : 10-12 Hours, Thoroughly Dry : 48 Hours. Can be polished after 12 hours at 20 °C
Is it possible to pre-mix your 2 pack gloss clearcoat then keep it in a jar for later use if not all used in one go, or is it a case of just mixing enough to do the job?
NO YOU MUST NOT DO THIS, once you mix the clear coat and hardener a chemical reaction is started, similar to epoxy glue or epoxy putty. It will hardened within 15/20 mins, if you mixed the lot you would be wasting product and money, so only mix whet you need each time, you will quickly find the amounts you need with a small amount of practice.
We would recommend starting with 10ml/gram or Clearcoat - 5ml/gram Hardener and 3ml of Thinners and see how much coverage you get wer fin this is plenty to clearcoat a 1:24 model with 3/4 coats.
Is this safe over decals
Yes, 2K Clearcoat is safe over decals, it has been tested on all the major brands : Tamiya, Fujimi, Aoshima, Studio 27, Cartograf, Scale Motorsport MFH, etc. Please remember to apply a few mist coats over the decals before the wet coats.
It has NOT been tested on homemade inkjet printed decals as so many brands exist, so please test on scrap first.
Is this safe over other paints
Yes, 2K Clearcoat is safe over most other paints (acrylic paint, Tamiya TS) once they are fully dry so please test on scrap first.
What do I clean my Airbrush and equipment with after use
The following products will work :- Airbrush Cleaner, Cellulose Thinners, Basecoat Thinners, 2k Thinners
but our Airbrush Cleaner is designed for the job and the cheapest
but our Airbrush Cleaner is designed for the job and the cheapest
[This stuff is the best!! I have never used as good as this clear coat. You wont use anything else, when you have used this! by Juha Pirilä]
People who bought this, also purchased these:
